|
SAFE WORK METHOD STATEMENT (Carpentry) Authorized By: _________________________
Rev: 1 06/12/2024 |
Logo Placeholder |
| COMPANY DETAILS | ||
| Name: XXX | ABN: XXX | Address: XXX |
| TASK NAME / ACTIVITY | Carpentry |
| SITE / PROJECT NAME | XXX |
| CODES OF PRACTICE | ||
| Construction work | Excavation work | Hazardous manual tasks |
| How to manage work health and safety risks | Managing electrical risks | Managing psychosocial hazards at work |
| Managing risks of falls at workplaces | Managing the risks of plant in the workplace | Work health and safety consultation, cooperation and coordination |
| PERSONAL PROTECTIVE EQUIPMENT | ||||||||
|
|
|
|
|
|
|
|
|
|
| HIGH RISK CONSTRUCTION WORK | ||
| Risk of a person falling more than 2 metres | Work on a telecommunication tower | Demolition of load-bearing structure |
| Likely to involve disturbing asbestos | Work on or near pressurised gas mains or piping | Work in or near a confined space |
| Work in or near a shaft or trench deeper than 1.5m or a tunnel | Use of explosives | Temporary load-bearing support for structural alterations or repairs |
| Work in or near water or liquid that involves a risk of drowning | Work on or near energised electrical installations or services | Work that may have a contaminated or flammable atmosphere |
| Tilt-up or precast concrete elements | Diving work | Work in an area with movement of powered mobile plant |
| Work in areas with artificial extremes of temperature | Work on or near chemical, fuel or refrigerant lines | Work on, in or adjacent to a road, railway, shipping lane or other traffic corridor in use by traffic other than pedestrians |
| Job / Task | Hazards / Risks | Initial Risk | Control Measures | Residual Risk | Responsibility |
|---|
| Accessing site and starting work | Traffic hazards | High |
Signage, flagging or delineation of work zone. Workers to be aware of traffic hazards. |
Medium | All workers |
| Contact with services | High |
Maintain exclusion zones around powerlines. Use spotters if necessary. DBYD and ensure underground services are protected prior to excavation. |
Medium | All workers | |
| Slips, trips and falls | High |
Good housekeeping. Wear non-slips shoes. Pay attention when walking. |
Medium | All workers | |
| Sunburn / dehydration | High |
Sun protection (broadbrimmed hard hat, sunscreen, long-sleeve clothing). Drink plenty of water. Avoid excessive caffeine. |
Low | All workers | |
| Electrical hazards | High |
Testing and tagging of electrical equipment. Run leads in a safe manner. Inspect electrical equipment before use. RCDs in use. |
Low | All workers | |
| Noise hazards | Medium |
Hearing protection to be worn if noise levels over 85dBA. Ensure loud plant or equipment is positioned away from workers, if possible. |
Low | All workers | |
| Chemical hazards | Medium |
Up to date SDS register available for all hazardous substances. All safety controls in place as per SDS. All spills to be reported to supervisor. Refer to SDS for chemical properties and storage/handling procedures. |
Low | All workers |
| Conducting carpentry work | Falls / injuries caused during carpentry works | High |
For works over 2m high (or 3m high in residential construction with roof pitch less than 26°), personnel are to ensure there is something physically stopping the worker from falling, e.g.: - Conducting the work off a solid construction - Using a fall prevention device (handrails etc.) - Conducting the work from a work platform - Using a fall restraint system - Using a fall arrest system. Staff are to be trained and competent in the use of safety equipment and procedures for working at heights (working at heights training may be required). Working at heights gear is to be fit for purpose and tested / tagged (if required). For works under 2m high, risks are to be assessed and managed. When working from ladders workers need to remember: - Only industrial ladders are to be used - Work from the top 2 rungs of a ladder is not permitted - Ladders and other working at heights equipment are to be inspected prior to use - Workers are to never lean or conduct heavy work off a ladder. |
Medium | All workers |
| Falling objects | High |
Personnel need to pay attention to signs and do not enter any exclusion zones established on site. All workers are to wear correct PPE. |
Medium | All workers | |
| Improper Use of Trestles | High |
When using trestles, workers must: Conduct a thorough inspection of trestles for any damage or defects before use. Secure trestles on a stable and level surface to prevent tipping. Utilize handrails or harnesses as necessary for additional safety. Adhere to weight capacity guidelines to avoid overloading trestles. |
Medium | All workers | |
| Improper Use of Mobile Scaffold | High |
When working with mobile scaffolds, workers must: Inspect the scaffold for any damage prior to use. Lock the wheels to prevent any unintended movement. Utilize guardrails and platforms as necessary for safety. Avoid overloading and strictly adhere to weight limits. |
Medium | All workers | |
| Incorrect Installation of Scaffolding | High |
Ensure: It is constructed by competent workers (a high-risk license is required if the scaffold exceeds 4 meters). The scaffold is fit for its intended purpose. It is placed on stable ground. It is equipped with guardrails, mid rails, and toe boards. Safe access is provided. caffolds identified as unsafe must be locked or tagged out. A competent person must inspect scaffolds before use: Following any alterations or repairs After events like high winds, storms, impacts, or unauthorized modifications that could compromise integrity or stability At regular intervals, not exceeding 30 days. |
Medium | All workers | |
| Use of Plant and Machinery - Crush injuries, Plant collisions, Plant rollovers | High |
Workers must maintain a safe distance from plant and machinery. Only competent and authorized personnel are permitted to operate them. Prohibited Actions: Lifting loads or attachments over workers Riding on machinery (unless in approved seating) Operating machinery under the influence of drugs or alcohol Using a phone while operating plant or machinery Ensure plant exclusion zones are established and enforced. Use spotters as needed. |
Medium | All workers | |
| Excavations - Contact with underground services, Unauthorised access, Trench collapse | High |
Before starting excavation work, personnel must ensure: Underground services are identified and marked using DBYD or service locators. Exclusion zones are set up according to the located services. If it's not possible to locate and mark all services, a full-time competent spotter should accompany the plant at all times. Unauthorized access near trenches must be prevented with barricades, fencing, and signage. Before entering a trench over 1.5 meters deep, workers must ensure: They have authorization, such as an excavation permit. Battering, benching, or shoring is in place. Safe access is available. |
Medium | All workers | |
| Improper Handling of Lifting Equipment | High |
Verify equipment approval and suitability. Conduct testing and tagging of gear. Set up exclusion zones. Inspect gear before use. Prohibited: Exceeding safe weight limits. Standing beneath suspended loads. Use taglines when needed. |
Medium | All workers | |
| Injuries from Hand and Power Tools | Medium |
Ensure workers are trained and competent in tool use. Inspect tools and cords for damage before use. Test and tag all electrical leads. |
Low | All workers | |
| Plant or Equipment Malfunction | Medium |
Complete pre-start checks. Ensure all guarding is in place and suitable. Report any faults to a supervisor. |
Low | All workers | |
| Incompetence with Plant/Equipment | Medium | Only allow competent and authorized personnel to perform tasks. | Low | All workers | |
| Plant Operation | High |
Restrict tasks to competent and authorized personnel. Implement and enforce exclusion zones. Use spotters when necessary. |
Medium | All workers | |
| Eye Injuries | Medium |
Restrict tasks to competent and authorized personnel. Ensure safety glasses are worn. Maintain all guarding. |
Low | All workers | |
| Hand Injuries | Medium |
Restrict tasks to competent and authorized personnel. Maintain all guarding. Wear appropriate gloves. |
Low | All workers | |
| Flying Debris | Medium |
Wear safety glasses (double eye protection for welding/grinding). Establish exclusion zones around hazardous areas. |
Low | All workers | |
| Silica Exposure | Medium |
Wet down areas to minimize dust. Use dust extraction on equipment if available. Wear respiratory PPE if dust levels are uncontrolled. |
Low | All workers | |
| Manual Handling Injuries | Medium |
Ensure all personnel are inducted. Use proper posture and handling techniques. Utilize mechanical devices. Implement team lifting. |
Low | All workers |
| Finishing Task / Packing Up | Equipment Damage During Shift | Medium | Report and tag out damaged equipment to a supervisor. | Low | All workers |
| Unauthorized Site Access | Medium | Secure gates and fences before leaving the site. | Low | All workers | |
| Slip, Trip, and Fall Risks | High |
Store tools and equipment properly. Dispose of all rubbish in bins. |
Low | All workers | |
| Handling Hazardous Materials | Medium | Store hazardous substances and flammables safely. | Low | All workers |
| Worker Sign off | Worker Sign off | ||
|---|---|---|---|
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |
| Name: | Signature: | Name: | Signature: |